Tutoriale Online

Tutoriale Online Invata Online cum se face si cum este corect. Learn Online How Must To Do !

Archive for the ‘Uncategorized’ Category

Online Tutoriale Adjusting Network Settings

Posted by ascultradio on September 3, 2009

Adjusting Network Settings :

Changing Network Adapter Settings

To check the speed and settings of network adapters, use the ethtool command which works now for most NICs. For example, to check the adapter settings of eth0 run:

# ethtool eth0

To force a speed change to 1000 full duplex, run:

# ethtool -s eth0 speed 1000 duplex full autoneg off

To make a speed change permanent for eth0, set or add the ETHTOOL_OPT environment variable in /etc/sysconfig/network-scripts/ifcfg-eth0


ETHTOOL_OPTS="speed 1000 duplex full autoneg off"

This environment variable is sourced in by the network scripts each time the network service is started.

Changing Network Kernel Settings

Oracle now uses UDP as the default protocol on Linux for interprocess communication, such as cache fusion buffer transfers between the instances. But starting with Oracle 10g network settings should be adjusted for standalone databases as well.

Oracle recommends the default and maximum send buffer size (SO_SNDBUF socket option) and receive buffer size (SO_RCVBUF socket option) to be set to 256 KB. The receive buffers are used by TCP and UDP to hold the received data for the application until it’s read. This buffer cannot overflow because the sending party is not allowed to send data beyond the buffer size window. This means that datagrams will be discarded if they don’t fit in the receive buffer. This could cause the sender to overwhelm the receiver

The default and maximum window size can be changed in the proc file system without reboot:

# sysctl -w net.core.rmem_default=262144  # Default setting in bytes of the socket receive buffer
# sysctl -w net.core.wmem_default=262144  # Default setting in bytes of the socket send buffer
# sysctl -w net.core.rmem_max=262144      # Maximum socket receive buffer size which may be set by using the SO_RCVBUF socket option
# sysctl -w net.core.wmem_max=262144      # Maximum socket send buffer size which may be set by using the SO_SNDBUF socket option

To make the change permanent, add the following lines to the /etc/sysctl.conf file, which is used during the boot process:


To improve failover performance in a RAC cluster, consider changing the following IP kernel parameters as well:


Changing these settings may be highly dependent on your system, network, and other applications. For suggestions, see Metalink Note:249213.1 and Note:265194.1.

On RHEL systems the default range of IP port numbers that are allowed for TCP and UDP traffic on the server is too low for 9i and 10g systems. Oracle recommends the following port range:

# sysctl -w net.ipv4.ip_local_port_range="1024 65000"

To make the change permanent, add the following line to the /etc/sysctl.conf file, which is used during the boot process:

net.ipv4.ip_local_port_range=1024 65000

The first number is the first local port allowed for TCP and UDP traffic, and the second number is the last port number.

Flow Control for e1000 NICs

The e1000 NICs don’t have flow control enabled in the 2.6 kernel, i.e RHEL 4. If you have heavy traffic, then the RAC interconnects may lose blocks, see Metalink Bug:5058952. For more information on flow control, see Wikipedia Flow control.

To enable Receive flow control for e1000 NICs, add the following line to the /etc/modprobe.conf file:

options e1000 FlowControl=1

The e1000 module needs to be reloaded for the change to take effect. Once the module is loaded with flow control, you should see e1000 flow control module messages in /var/log/messages.

Posted in Uncategorized | Tagged: , | Leave a Comment »